Here’s a look at some tools customers can’t do without
In the 1970s, growing up in southeast Missouri, my weekends and summer breaks were spent working in my uncle’s saw mill and on my grandpa’s farm in the hayfields. As I look back, it amazes me how technology has changed in these professions and virtually everything we do today. Kansas City, Mo.-based Dynamic Fastener has been in the tool and fastener industry for more than 35 years and continues to see changes, advancements and improved ways in the metal building industry. We constantly provide our customers with the newest technology and equipment for erecting metal buildings. Based on feedback from metal building contractors, here are some of the most popular products customers can’t do without.
Slasher steel cutting blades
The Slasher metal cutting saw blade for circular saws is the perfect blade when you need to cut a painted panel. As compared to using an abrasive wheel, you’ll obtain: 1) less noise; 2) fewer blade changes; 3) no burr on edges; 4) drastically reduced sparking; 5) less cost per cut; 6) no dust clouds; 7) faster cutting; and 8) cool cutting. Use this blade to cut mild steel in: sheet steel, 1/4- inch thick plate, steel studs, steel pipe, channel, threaded rod and much more. Ten-inch and larger blades are designed for low RPM saws. They are not for use with standard chop saws or standard miter saws.
![]() |
Versa-bender
The Versa-bender fabricates metal such as counter flashing, saddles, fascia, tile pans and metal panels on the job site. It quickly adjusts to the desired bending depth of 5/8- to 7 1/2-inch, and bends metal along a continuous line up to 90 degrees by sliding rollers back and forth along edge of steel. It bends 24-gauge painted metal and 0.040-aluminum. The double-station Versa-bender has an additional set of rollers to allow for maximum efficiency, better uniform bending and less operator fatigue as compared to the original single-station Versa-bender.
Versa-hemmer
The Versa-hemmer complements the Versa-bender by completing the 90-degree bend to a complete 180-degree fold. It can also bend 24-gauge painted metal and 0.040-aluminum. Simply insert the metal that is already bent to 90 degrees between the metal disc and the rollers. Slowly slide the disc back and forth to gradually bend the edge of the metal down to 180 degrees. The Versa-hemmer is great for hemming panels for valleys, rake edges and interlocking metal.
Safe-T ladder extension system
You may not think of this product as a tool, but is definitely a must when using extension ladders. The Safe-T ladder extension system is designed to attach over the top of the extension ladder and provide a safe and easy transition from the ladder to a second surface. Made of 6061 T6 aluminum, this product requires no tools, drilling or bolting to be held securely in place. The simple-to-use knob tightens by hand without scratching or damaging the ladder. Once installed, the unit provides two offsetting handrails that can be used to walk through, and step on or off the ladder. Those awkward and dangerous maneuvers when entering and exiting at the top of your extension ladder will be eliminated with this product.
![]() |
Scrugun
There are a variety of scruguns available for different applications. When installing self-drilling screws it is critical to use the proper scrugun. Drilling through 1/4-inch or thicker steel it is very important to use a slow RPM/high-torque scrugun. The DeWalt 269 with 1,000 RPM is a perfect example of a suitable tool. When attaching sheet to sheet, or sheet to purlin, a 2,500 RPM scrugun, such as the DeWalt 268, is recommended.
Fein nibbler
The BLK 1.3CS nibbler can cut flat or corrugated sheet metal up to 18-gauge thick. Cutting speed is 7 1/2 feet per minute. Rotating punch system increases punch life by 30 percent. Eight die locations allow cutting direction to be adjusted in 45-degree increments without tools.
Tool and fastener handguide
Finally, when talking about tools for metal construction, there’s a valuable product we supply annually to our metal building contractors. Dynamic Fastener releases the newest version of its tool and fastener handguide every April, providing answers to many issues, common and uncommon, that arise in the metal building industry. The free, 124-page, full-color publication offers answers to questions pertaining to fastener applications, engineering data, availability of types, size ranges and fastener materials. In addition to discussing screws and anchors, the guide provides prices and other information relating to the products in this article, plus many other tools, fall protection, fasteners and flashings that are available for metal construction. Yes, technology sure has changed from the days working in Uncle Chris’ saw mill and on the farm with Grandpa Renner. Just like these occupations, the metal building industry will continue to change for the better. Ken Webb has been involved in the metal construction industry for the past 25 years with Dynamic Fastener, Kansas City, Mo. To learn more, visit www.dynamicfastener.com.








