Columns

Coil Coatings for High Performance

Advanced coil coating technology produces higher quality goods The evolution of advanced continuous coil coating technology in the 30 years since it was first introduced to the market has been astonishing. Cost overruns, paint waste, ingot scrap and long turnaround times once associated with the fabrication process-and part of the standard cost of doing business-are… Continue reading Coil Coatings for High Performance

Advanced coil coating technology produces higher quality goods

The evolution of advanced continuous coil coating technology in the 30 years since it was first introduced to the market has been astonishing. Cost overruns, paint waste, ingot scrap and long turnaround times once associated with the fabrication process-and part of the standard cost of doing business-are no longer issues. Advanced coil coating technology not only produces higher quality finished goods; it enables a process that is cost-effective, efficient and eco-friendly.

The process

The coil coating process allows us to produce unlimited quantities of material with uniform color, from run to run. Line conditions are tightly controlled to achieve the maximum results. Both sides of the material are cleaned, pre-treated, primed, oven-cured and painted in the same operation. On a coil coating line, the metal is painted in the flat, allowing coaters to clean and coat both sides evenly, achieving the optimum surface conditions necessary to produce a durable, flexible and corrosion-resistant finish.

A special coating head rolls paint onto the coil in a smooth, uniform film that is applied in very thin, precise layers. Up to four different coats of paint can be applied in one operation: primer on both sides, a finish coat on the top and a wash coat on the bottom. The paint is then cured into a hard, durable finish.

Cutting-edge coatings

Advanced continuous coil coating technology is used to apply Eastman, Ga.-based Alcoa Architectural Products’ latest cutting-edge coatings like Reynobond with EcoClean and Reynobond Design Line. Applied over the architectural painted aluminum composite material (ACM) specified by the architect, EcoClean provides two important solutions to the painted metal market: it is self-cleaning and it helps to clean the air around it. The coating creates a hydrophilic surface that allows water to pull dirt and residue from the surface. EcoClean also provides a photocatalytic surface which, when energized by the sun, breaks down and destroys organic dirt and airborne smog. Titanium Dioxide (TiO2) particles in the coating use water and oxygen molecules to develop powerful oxidizers. The coating is applied over a barrier coat so none of the organic pigments in the coating are consumed in the process. With its cleaning powers, EcoClean has the potential to reduce the lifetime maintenance costs of a building and improve the performance of reflective coatings.

Tiff Transfer
Mark Kempf Photography, St. Louis)

Coil-coated Design Line paint finishes are almost indistinguishable from natural granite, wood, travertine and terra cotta. They provide valuable alternate options that allow architects to capture natural aesthetics without mining any irreplaceable stone or cutting down any trees. The flexible nature of the material gives architects the freedom to design without the restrictions imposed by the weight and properties of the natural materials. By employing continuous coil coating technology, rather than a film, Design Line patterns can be easily matched on an unlimited number of panels, profile panels and on flat sheet fabricated for flashing materials. This enables the fabricator to maintain the consistency of color and pattern throughout a project.

The right paint for the job

No one paint system meets the criteria for every job. Colors, gloss, range, hardness, chemical resistance and UV durability all influence the selection of the primary paint system.

The marriage of aluminum and Kynar produces an architectural panel that outperforms all others, including steel panels finished with Kynar coatings. Alcoa offers three levels of coil-coated Kynar finishes for Reynobond, Reynolux Profile and flat sheet. Each coating is formulated to provide a solution to a different architectural need. Duragloss 5000 paint finishes, with a 20-year finish warranty, performs well on cladding, exterior wall panels and trim. Duragloss 3000 paint finishes, with a 10-year finish warranty, allows for your very high gloss vibrant finishes. These are used for corporate identity such as auto dealerships, gas station canopies and convenience store fascia.

The premium, high-performance Colorweld 500 coatings by Alcoa exceed AAMA 2605-98 requirements for long-term durability and performance. Comprised of 70 percent Kynar 500/Hylar 5000 polyvinylidene fluoride (PVDF) resins with Fluoropolymer technology, they provide excellent flexibility and film adhesion for forming and superior resistance to salt sea spray, humidity, impact, pollution and abrasion. With a 30-year finish warranty, outstanding color and gloss retention, and improved hardness and durability, they’ve raised the bar for premier architectural coatings. Continuous coil coating paint finishes are a cost-effective choice that enhances the properties of architectural metal materials. By choosing the right coil-coated paint finish for the job, you can enrich the look and longevity of a project, while improving your bottom line.

George Rosado is the commercial director of Alcoa Architectural Products, Eastman, Ga. To learn more, visit www.reynobond.com.